BS EN 10210-1 PDF

Art

This revision permits the publication of BS EN to be adopted as a Harmonised Standard under the Constuction Products Directive. BS EN. Hot finished structural hollow sections of non-alloy and fine grain steels -. Part 1: Technical delivery conditions d Copy. Find the most up-to-date version of BS EN at Engineering

Author: Shanris Nira
Country: Russian Federation
Language: English (Spanish)
Genre: Life
Published (Last): 4 February 2005
Pages: 65
PDF File Size: 15.85 Mb
ePub File Size: 9.2 Mb
ISBN: 292-1-52191-477-4
Downloads: 6409
Price: Free* [*Free Regsitration Required]
Uploader: Dakazahn

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Octoberand conflicting national standards shall be withdrawn at the latest by October An FPC system conforming with the requirements of EN ISOand made specific to the product and the requirements of this standard, shall be considered to satisfy the above requirements.

Take the smart route to manage medical device compliance. Users of British Standards should make sure that they possess the latest amendments or editions. Technical delivery conditions for non-alloy structural steels ENHot rolled products of structural steels — Part 3: Supersedes BS EN The scope of this annex is defined by Table ZA. This standard consists of the following parts under the general title ‘Hot finished structural hollow sections of non-alloy and fine grain steels’: Profils creux pour la construction finis a chaud en aciers non allies et a grains fins.

  KORONER ANJIYOGRAFI PDF

BS EN for Hot Finished Structural Hollow Sections

To consider the test unit as conforming after testing the second set, the following conditions shall all be satisfied simultaneously: A test unit is defined as a quantity of hollow sections from one or more cast s of the same grade and dimensions, manufactured by the same process i.

During the design process itself, a record shall be kept of all checks, their results, and 1010-1 corrective actions taken. For undated references, the latest edition of the referenced document including any amendments applies.

If the nominal product thickness is not sufficient for the preparation of standard test pieces, the test shall be carried out using test pieces of width less than 10 mm, but not less than 5 mm. NOTE Cold formed hollow sections with subsequent heat treatment to obtain properties equivalent to those obtained by normalizing rolling are deemed to meet the requirements of this standard. Tolerances, dimensions and sectional properties It forms part of a series of standards 10201-1 hollow sections together rn EN and 2, which are also under revision.

In case of dispute, the method used shall be agreed taking into account CR The following performance characteristics are not subject bw initial type testing for the following reasons: This record shall be sufficiently detailed and accurate to demonstrate that all stages of the design phase, and all checks, have been carried out satisfactorily.

  ALFONSO USSIA LIBROS PDF

BS EN 10210-1:2006

The purchaser should preferably select hollow section dimensions from this limited range of sizes. It presents the UK view on standards in Europe bd at the international level.

Structural hollow sections of fine grain steels shall conform to the requirements of Annex B. Other requirements and other EU Directives, not affecting the fitness for intended use may be applicable to a bd product falling within the scope of this standard. Longitudinal or transverse samples at the discretion of the manufacturer.

The inspection certificate shall contain the following codes and related information in accordance with EN Carbon and low alloy steels ISO Table 4 — Test units Licensed Copy: Copyright Copyright subsists in all BSI publications. The results of inspections, eh or assessments requiring action shall be recorded, as shall any corrective action taken. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have 1010-1 published as British Standards, unless otherwise requested.

Hollow section for general applications

Document Status Indicators The Green document status indicator indicates that the document is: Revisions British Standards are updated by amendment or revision. Click here to find out how to access this document. The operating authorisation issued by the employer shall be in accordance with a written procedure.